9. Frequently Asked Questions

9.1. How do I keep my script running?

The following script looks like it should turn an LED on:

from gpiozero import LED

led = LED(17)

And it does, if you’re using the Python (or IPython or IDLE) shell. However, if you saved this script as a Python file and ran it, it would flash on briefly, then the script would end and it would turn off.

The following file includes an intentional pause() to keep the script alive:

from gpiozero import LED
from signal import pause

led = LED(17)


Now the script will stay running, leaving the LED on, until it is terminated manually (e.g. by pressing Ctrl+C). Similarly, when setting up callbacks on button presses or other input devices, the script needs to be running for the events to be detected:

from gpiozero import Button
from signal import pause

def hello():

button = Button(2)
button.when_pressed = hello


9.2. My event handler isn’t being called

When assigning event handlers, don’t call the function you’re assigning. For example:

from gpiozero import Button

def pushed():
    print("Don't push the button!")

b = Button(17)
b.when_pressed = pushed()

In the case above, when assigning to when_pressed, the thing that is assigned is the result of calling the pushed function. Because pushed doesn’t explicitly return anything, the result is None. Hence this is equivalent to doing:

b.when_pressed = None

This doesn’t raise an error because it’s perfectly valid: it’s what you assign when you don’t want the event handler to do anything. Instead, you want to do the following:

b.when_pressed = pushed

This will assign the function to the event handler without calling it. This is the crucial difference between my_function (a reference to a function) and my_function() (the result of calling a function).


Note that as of v1.5, setting a callback to None when it was previously None will raise a CallbackSetToNone warning, with the intention of alerting users when callbacks are set to None accidentally. However, if this is intentional, the warning can be suppressed. See the warnings module for reference.

9.3. Why do I get PinFactoryFallback warnings when I import gpiozero?

You are most likely working in a virtual Python environment and have forgotten to install a pin driver library like RPi.GPIO. GPIO Zero relies upon lower level pin drivers to handle interfacing to the GPIO pins on the Raspberry Pi, so you can eliminate the warning simply by installing GPIO Zero’s first preference:

$ pip install rpi.gpio

When GPIO Zero is imported it attempts to find a pin driver by importing them in a preferred order (detailed in API - Pins). If it fails to load its first preference (RPi.GPIO) it notifies you with a warning, then falls back to trying its second preference and so on. Eventually it will fall back all the way to the native implementation. This is a pure Python implementation built into GPIO Zero itself. While this will work for most things it’s almost certainly not what you want (it doesn’t support PWM, and it’s quite slow at certain things).

If you want to use a pin driver other than the default, and you want to suppress the warnings you’ve got a couple of options:

  1. Explicitly specify what pin driver you want via the GPIOZERO_PIN_FACTORY environment variable. For example:

    $ GPIOZERO_PIN_FACTORY=pigpio python3

    In this case no warning is issued because there’s no fallback; either the specified factory loads or it fails in which case an ImportError will be raised.

  2. Suppress the warnings and let the fallback mechanism work:

    >>> import warnings
    >>> warnings.simplefilter('ignore')
    >>> import gpiozero

    Refer to the warnings module documentation for more refined ways to filter out specific warning classes.

9.4. How can I tell what version of gpiozero I have installed?

The gpiozero library relies on the setuptools package for installation services. You can use the setuptools pkg_resources API to query which version of gpiozero is available in your Python environment like so:

>>> from pkg_resources import require
>>> require('gpiozero')
[gpiozero 1.4.1 (/usr/lib/python3/dist-packages)]
>>> require('gpiozero')[0].version

If you have multiple versions installed (e.g. from pip and apt) they will not show up in the list returned by the pkg_resources.require() method. However, the first entry in the list will be the version that import gpiozero will import.

If you receive the error “No module named pkg_resources”, you need to install pip. This can be done with the following command in Raspbian:

$ sudo apt install python3-pip

Alternatively, install pip with get-pip.

9.5. Why do I get “command not found” when running pinout?

The gpiozero library is available as a Debian package for Python 2 and Python 3, but the pinout tool cannot be made available by both packages, so it’s only included with the Python 3 version of the package. To make sure the pinout tool is available, the “python3-gpiozero” package must be installed:

$ sudo apt install python3-gpiozero

Alternatively, installing gpiozero using pip will install the command line tool, regardless of Python version:

$ sudo pip3 install gpiozero


$ sudo pip install gpiozero

9.6. The pinout command line tool incorrectly identifies my Raspberry Pi model

If your Raspberry Pi model is new, it’s possible it wasn’t known about at the time of the gpiozero release you are using. Ensure you have the latest version installed (remember, the pinout tool usually comes from the Python 3 version of the package as noted in the previous FAQ).

If the Pi model you are using isn’t known to gpiozero, it may have been added since the last release. You can check the GitHub issues to see if it’s been reported before, or check the commits on GitHub since the last release to see if it’s been added. The model determination can be found in gpiozero/pins/data.py.

9.7. What’s the gpiozero equivalent of GPIO.cleanup()?

Many people ask how to do the equivalent of the cleanup function from RPi.GPIO. In gpiozero, at the end of your script, cleanup is run automatically, restoring your GPIO pins to the state they were found.

To explicitly close a connection to a pin, you can manually call the close() method on a device object:

>>> led = LED(2)
>>> led.on()
>>> led
<gpiozero.LED object on pin GPIO2, active_high=True, is_active=True>
>>> led.close()
>>> led
<gpiozero.LED object closed>

This means that you can reuse the pin for another device, and that despite turning the LED on (and hence, the pin high), after calling close() it is restored to its previous state (LED off, pin low).

9.8. How do I use button.when_pressed and button.when_held together?

The Button class provides a when_held property which is used to set a callback for when the button is held down for a set amount of time (as determined by the hold_time property). If you want to set when_held as well as when_pressed, you’ll notice that both callbacks will fire. Sometimes, this is acceptable, but often you’ll want to only fire the when_pressed callback when the button has not been held, only pressed.

The way to achieve this is to not set a callback on when_pressed, and instead use when_released to work out whether it had been held or just pressed:

from gpiozero import Button

Button.was_held = False

def held(btn):
    btn.was_held = True
    print("button was held not just pressed")

def released(btn):
    if not btn.was_held:
    btn.was_held = False

def pressed():
    print("button was pressed not held")

btn = Button(2)

btn.when_held = held
btn.when_released = released

9.9. Why do I get “ImportError: cannot import name” when trying to import from gpiozero?

It’s common to see people name their first gpiozero script gpiozero.py. Unfortunately, this will cause your script to try to import itself, rather than the gpiozero library from the libraries path. You’ll see an error like this:

Traceback (most recent call last):
  File "gpiozero.py", line 1, in <module>
    from gpiozero import LED
  File "/home/pi/gpiozero.py", line 1, in <module>
    from gpiozero import LED
ImportError: cannot import name 'LED'

Simply rename your script to something else, and run it again. Be sure not to name any of your scripts the same name as a Python module you may be importing, such as picamera.py.

9.10. Why do I get an AttributeError trying to set attributes on a device object?

If you try to add an attribute to a gpiozero device object after its initialization, you’ll find you can’t:

>>> from gpiozero import Button
>>> btn = Button(2)
>>> btn.label = 'alarm'
Traceback (most recent call last):
  File "<stdin>", line 1, in <module>
  File "/usr/lib/python3/dist-packages/gpiozero/devices.py", line 118, in __setattr__
    self.__class__.__name__, name))
AttributeError: 'Button' object has no attribute 'label'

This is in order to prevent users accidentally setting new attributes by mistake. Because gpiozero provides functionality through setting attributes via properties, such as callbacks on buttons (and often there is no immediate feedback when setting a property), this could lead to bugs very difficult to find. Consider the following example:

from gpiozero import Button

def hello():

btn = Button(2)

btn.pressed = hello

This is perfectly valid Python code, and no errors would occur, but the program would not behave as expected: pressing the button would do nothing, because the property for setting a callback is when_pressed not pressed. But without gpiozero preventing this non-existent attribute from being set, the user would likely struggle to see the mistake.

If you really want to set a new attribute on a device object, you need to create it in the class before initializing your object:

>>> from gpiozero import Button
>>> Button.label = ''
>>> btn = Button(2)
>>> btn.label = 'alarm'
>>> def press(btn):
...:    print(btn.label, "was pressed")
>>> btn.when_pressed = press

9.11. Why is it called GPIO Zero? Does it only work on Pi Zero?

gpiozero works on all Raspberry Pi models, not just the Pi Zero.

The “zero” is part of a naming convention for “zero-boilerplate” education friendly libraries, which started with Pygame Zero, and has been followed by NetworkZero, guizero and more.

These libraries aim to remove barrier to entry and provide a smooth learning curve for beginners by making it easy to get started and easy to build up to more advanced projects.